雜質去除?

Impurity removal

合金尾氣含粉塵等雜質，會磨損發動機部件。需在進氣管道前端設旋風、布袋等高效除塵設備。如某銅合金廠起初未除塵，發動機運行三月后嚴重磨損，加裝布袋除塵器后，除塵效率超 99%，問題解決。?

Alloy exhaust contains impurities such as dust, which can wear down engine components. Efficient dust removal equipment such as cyclones and bags should be installed at the front end of the intake duct. If a copper alloy factory initially did not remove dust, the engine would suffer severe wear after running for three months. After installing a bag filter, the dust removal efficiency exceeded 99%, and the problem was solved. ?

成分調節?

Ingredient regulation

尾氣中一氧化碳、氫氣等可燃成分濃度要合適，否則燃燒不穩定甚至有爆炸風險?？裳b在線氣體分析儀，配自動調節裝置，依濃度調節尾氣與空氣混合比例。如鋅合金冶煉尾氣發電項目，用 PLC 系統依分析儀數據，自動調進氣閥門開度，穩定可燃成分濃度。?

The concentration of combustible components such as carbon monoxide and hydrogen in exhaust gas should be appropriate, otherwise the combustion will be unstable and there may even be a risk of explosion. Can be equipped with an online gas analyzer, equipped with an automatic adjustment device, to adjust the mixing ratio of exhaust gas and air according to concentration. For the zinc alloy smelting tail gas power generation project, a PLC system is used to automatically adjust the opening of the intake valve based on analyzer data, stabilizing the concentration of combustible components. ?

溫度控制?

Temperature control

尾氣溫度常過高，會降低潤滑油黏度、引發爆震。要設水冷式換熱器等冷卻裝置，降低尾氣溫度。某鋁合金廠尾氣從 400℃冷卻至 150℃，滿足了發電機組進氣要求。

The exhaust temperature is often too high, which can reduce the viscosity of lubricating oil and cause detonation. Cooling devices such as water-cooled heat exchangers should be installed to reduce the exhaust gas temperature. The exhaust gas from a certain aluminum alloy factory was cooled from 400 ℃ to 150 ℃, meeting the intake requirements of the generator set.

發電參數監測?

Power generation parameter monitoring

密切留意輸出電壓、電流、頻率。電壓不穩易損用電設備，頻率偏差影響電力質量與電網接入。通過智能電表和電力監測系統采集數據，參數異常時自動報警并調節。如某鎳合金發電站用遠程監控系統，電壓波動 ±5% 時，系統自動調勵磁電流穩定電壓。?

Pay close attention to the output voltage, current, and frequency. Unstable voltage can easily damage electrical equipment, and frequency deviation affects power quality and grid connection. Data is collected through smart meters and power monitoring systems, and automatic alarms and adjustments are made when parameters are abnormal. If a nickel alloy power station uses a remote monitoring system, when the voltage fluctuates by ± 5%, the system automatically adjusts the excitation current to stabilize the voltage. ?

發動機狀態監測?

Engine condition monitoring

發動機是核心，要監測機油壓力、冷卻液溫度、轉速等。機油壓力低影響潤滑，冷卻液溫度高易致發動機過熱。通過壓力、溫度等傳感器傳輸數據，實現故障預警。某鈷合金廠在發動機裝多個傳感器，提前發現并解決多次潛在故障。

The engine is the core and needs to monitor oil pressure, coolant temperature, speed, etc. Low oil pressure affects lubrication, and high coolant temperature can easily cause engine overheating. By transmitting data through sensors such as pressure and temperature, fault warning can be achieved. A certain cobalt alloy factory installed multiple sensors in the engine to detect and solve potential faults in advance.

尾氣排放監測?

Exhaust emission monitoring

發電時仍要監測尾氣排放，安裝設備監測二氧化硫、氮氧化物、顆粒物等濃度，確保達標。超標時排查燃燒、尾氣處理裝置等問題并整改。如某鉛合金廠因活性炭吸附飽和未換，致二氧化硫超標停產，更換并加強監測后復產。?

During power generation, it is still necessary to monitor exhaust emissions and install equipment to monitor concentrations of sulfur dioxide, nitrogen oxides, particulate matter, etc., to ensure compliance with standards. When exceeding the standard, investigate and rectify issues with combustion and exhaust treatment devices. If a lead alloy factory fails to replace activated carbon due to saturation adsorption, resulting in excessive production of sulfur dioxide, it will resume production after replacement and strengthened monitoring. ?

防火防爆措施?

Fire and explosion prevention measures

合金尾氣易燃易爆，運行區要設防火隔離帶，嚴禁煙火。安裝可燃氣體泄漏報警裝置，搭配通風系統。電氣設備采用防爆型，避免電火花引發爆炸。某鎂合金廠車間裝多個探測器，全方位監測泄漏，保障安全。

Alloy exhaust gas is flammable and explosive. Fire isolation zones should be set up in the operating area, and smoking and open flames are strictly prohibited. Install a combustible gas leak alarm device and equip it with a ventilation system. The electrical equipment adopts explosion-proof type to avoid explosions caused by electric sparks. Multiple detectors are installed in the workshop of a magnesium alloy factory to comprehensively monitor leaks and ensure safety.

本文由合金尾氣發電機組友情奉獻.更多有關的知識請點擊:http://www.esonled.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message